Uncropped image of a rider
I recently took pictures at a bike ride, discussed in an earlier post. My intention was to get pictures of one particular participant, and not necessarily cover the race in general. This changed when I didn’t see other photographers around, and was confirmed when riders waved at me like they were expecting their picture to be taken.
I was a little disappointed with some of the results. Initially I put it down to inadequate preparation and not scouting the course for good shooting locations, but later realized the real problem was inappropriate camera settings. I make a habit of running through a checklist before each shoot, then if time permits, re-checking during the shoot. For the first part of the event, I overlooked this essential step. Later while reviewing my list, I felt it needed an update, and thought it might be a good idea to share it. The list is based on the Nikon D200 camera, a few years old, but still pretty sophisticated. Camera features and controls differ from model to model, and different manufacturers may have their unique nomenclature, but your camera should have similar functions, so you should be able to translate the steps.
Detail of Lucky Shot - less than recommended - shot at 1/160th and 200mm.
Modern cameras, even simple point-and-shoot’s, can have a bewildering combination of settings. I approach most shoots with pretty much the same setup. These lists help me to prepare for and think through the shoot, make any camera adjustments, but most important, reset any changes from the last time out.
On the subject of confusing camera settings, if you don’t have a “Cheat Sheet” for your camera, I suggest you make or buy one. I purchased a laminated version together with my camera. It’s by Bert Sirkin at
www.photocheatsheets.com
7 Essential Camera Pre-Shoot Checks
1. Quality: Set to RAW. I shoot almost exclusively in RAW mode, but occasionally I will change to highest quality JPEG.
2. ISO: This depends on the shoot. Action at ISO 400, general subjects at ISO 200, and studio or high quality at ISO 100. With this camera, noise is noticeable at about ISO 800, so I avoid going there! Current high end cameras offer much better noise control at higher ISO’s.
3. White Balance: If light conditions are changing frequently, set WB to Auto, otherwise set to the appropriate setting for daylight, cloudy, flash etc. If the conditions are stable, like in the studio, set to a custom value via a gray card target. I use a 14” Pocket Digital Calibration Target from Photovision.
4. Exposure Mode: Aperture Priority. Most of the time I use Aperture Priority, sometimes Manual, seldom Shutter priority, and never Program mode. Aperture Priority is my personal preference, a hang over from the early days of exposure automation adopted by Pentax (my first real camera) and Nikon. Aperture Priority is better suited for static subjects, while Shutter Priority is better suited for action.
5. Exposure Compensation: Turn Off. Some situations call for over or under exposure, but remember to reset to normal afterwards!
6. Focus: This consists of several settings, and varies by manufacturer and model. My preferences are:
- Camera: Usually set to AF C-Continuous (constantly tries to re-focus on moving subjects while the shutter is pressed 1/2 way), sometimes AF S-Single (focus and hold when shutter is pressed half-way) or AF M-Manual.
- Auto Focus Area: my order of preference.
- Single: One small selectable focus area – good for stationary subjects or action where subject moves on a predictable path.
- Group Dynamic: Select a group of focus areas, the camera will follow within the group – good for action within a small area.
- Dynamic Area: multiple focus areas, if the subject moves to a different area the camera will follow – good for unpredictable action.
- Dynamic Area Closest Subject: Focus on the closest subject – good for action when there is nothing between you and the subject.
- Lens: If the lens has an auto focus switch, set it to Off when the camera is set to AF M-Manual, otherwise set to On.
- Manual Focus: Set camera to one of the AF areas (usually a Single area), then you can use the viewfinder display to confirm manual focus.
7. Lens Aperture: Start by setting the lens to 2 stops down from wide open. Example: for a f 2.8 lens set to f5.6, for a f4 lens set to f8. Note: Nikon G lenses, don’t have a physical ring to set the aperture, but other lenses do. On these non-G lenses, exposure can’t be calculated correctly unless the lens is manually set (and locked) to the smallest aperture.
5 Essential Camera Shooting Checks
Ideally these should be done before every picture, but at least before each set or when conditions change. I’m pretty good with the first step, but for the rest, not so much!
1. Auto focus area: try to lock the focus area onto the subject, or choose the appropriate AF area from step 6 above.
2. Aperture: Open up to throw the background out of focus or when more light is needed; stop down to increase depth of field at the expense of sharpness. Avoid the f-stops at both extremes of the lens. If the lens has any shortcomings they will show up there.
3. Shutter Speed: For hand-held shots without vibration reduction, always try to keep the shutter speed above the reciprocal of focal length of lens. In plain English, with a 50mm lens, shoot at 1/60th or higher, with a 200mm lens, shoot at 1/250th or higher. This is a long-standing guideline for 35mm film cameras, but still applies for cameras with smaller sensors. If you can’t meet this then either choose a wider aperture, a higher ISO, add some light, or use some tool to steady the camera – a tripod, beanbag or turn on vibration reduction if you have it.
4. ISO: When shooting on location, the light may brighten or fade, and eventually exceed the recommended limits of aperture and shutter speed. If there is no way to modify the light, the ISO will have to be changed.
5. White Balance: Unless this is set to auto, check frequently. This is essential when shooting in JPEG mode, less important when shooting in RAW mode.
Bonus: Other settings that I change occasionally and forget to reset!
• Shutter Delay: For situations where a long exposure is used, this delays the shutter by about ½ second and reduces vibrations caused by the mirror and camera itself. This is a Menu setting.
• Shoot only when in focus: Usually this is set to shoot when I press the shutter, but sometimes I’ll set the camera to fire only when focus is confirmed. I find this works well when AF is set to S-Single, but not so good when set to C-Continuous. This is a Menu Setting.
• Pop-up flash exposure compensation: I very seldom use the camera’s pop-up flash, but when I do its usually set to -1 or -2 stops for daylight fill-flash.
• Optimize Image: When shooting in RAW mode I never change these settings, but they are checked just in case. Effectively they are “turned off”; Image Sharpening: -2 (low); Tone Compensation: – (low); Color Mode: II (with Adobe RGB color space); Color Saturation: – (moderate); Hue Adjustment: 0 (neutral).
Adapt these lists to your camera and shooting style. Use them and one day you’ll avoid the feeling that your timing or perception are way off, when it’s really just your camera with a “hangover” from your previous shoot.
________________________________________
Duncan Moody
www.sabelaimages.com
